Expert HVAC solutions for homes and businesses across Eagle Pass, TX. Certified technicians, transparent pricing, and results you can count on.
Browse our full range of heating, cooling, and air quality services available in your area.
When your boiler produces inconsistent heat, unusual noises, or pressure fluctuations, the root cause often involves sediment buildup, failing motorized valves, or degraded seals within the hydronic loop. Experienced technicians restore system balance and verify safe operation through combustion analysis.
Ductwork problems manifest as uneven room temperatures, excessive dust near registers, and HVAC systems that run continuously without satisfying the thermostat. Technicians identify crushed flex runs, separated joints, and deteriorated mastic seals using pressure testing and visual inspection protocols.
A comprehensive furnace tune-up includes combustion analysis, heat exchanger inspection, and verification of gas pressure at the manifold. Technicians clean burners, test flame sensor microamp readings, and confirm proper flue draft to maintain safe, efficient operation throughout the heating season.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
Upgrading to a modern heat pump delivers dual-mode heating and cooling from a single system, with top-tier models achieving 10+ HSPF and 20+ SEER2 ratings. Proper installation includes Manual J load calculations, refrigerant line sizing, and electrical panel verification for reliable year-round comfort.
Comprehensive HVAC inspections cover thermostat operation, ductwork condition, refrigerant levels, electrical connections, and combustion safety. This detailed assessment identifies efficiency losses, safety hazards, and components nearing end of service life before they result in costly emergency repairs.
Full HVAC installation requires coordination of heating equipment, cooling components, ductwork design, and control systems to deliver efficient comfort at rated capacity. Our technicians perform Manual J and Manual D calculations, size equipment to match your structure, and commission the system to manufacturer standards.
An annual air conditioning tune-up catches refrigerant leaks, worn contactor points, and degraded fan motors before they cascade into compressor damage. Technicians measure temperature differential across the coil, verify amp draws, and confirm proper subcooling to protect your investment.
A dryer that takes multiple cycles to dry clothes or feels excessively hot to the touch signals a restricted vent line. Technicians clear lint accumulation using rotary brush systems and compressed air, then verify exhaust velocity meets manufacturer specifications for safe, efficient operation.
Heat pumps rely on a precise balance of refrigerant pressure, electrical components, and airflow to deliver efficient heating and cooling year-round. Professional repair addresses compressor hard starts, frozen coils, faulty thermostatic expansion valves, and auxiliary heat lockout conditions.
Clean ductwork directly impacts the efficiency of your HVAC system by reducing static pressure and allowing unrestricted airflow to every register. Our technicians inspect for microbial growth, seal access points after service, and verify airflow improvements with anemometer readings post-cleaning.
When a mini-split displays error codes, produces weak airflow, or fails to reach setpoint, the fault often lies within the inverter board, thermistor sensors, or refrigerant circuit. Professional repair restores rated SEER output and eliminates the inefficient short cycling that drives up utility costs.
Smart thermostats from Ecobee, Nest, and Honeywell Home offer occupancy sensing, geofencing, and learning algorithms that adapt to your schedule automatically. Our technicians verify system compatibility, install the required wiring, and configure the device for optimal interaction with your specific HVAC equipment.
When your heating or cooling system fails unexpectedly, rapid diagnosis is critical to minimizing discomfort and preventing secondary damage like frozen pipes or heat-related illness. Emergency technicians isolate the fault, whether electrical, mechanical, or refrigerant-related, and execute repairs on the spot.
Restoring reliable air conditioning performance requires more than replacing visible parts. Technicians measure refrigerant pressures, check compressor winding resistance, test run and start capacitors, and verify condenser fan operation to ensure every component of the cooling circuit functions within specification.
KIC Refrigeration is trusted by property owners throughout Eagle Pass (pop. 29,075) for a simple reason — we do what we say we are going to do. No inflated repair estimates, no recommending replacements when a repair will do, and no disappearing after the invoice is paid. We are here for the long term and our reputation across Eagle Pass reflects that commitment to honesty.
Our commitment to the Eagle Pass community goes beyond HVAC service. We hire locally, support Texas suppliers when possible, and stand behind every installation and repair with warranties that actually mean something. When your heating or cooling system needs attention, choose the company that Eagle Pass homeowners already trust with their comfort.
What makes us different from every other heating and cooling company in the area.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
HVAC failures do not wait for business hours and neither do we. Our emergency technicians are dispatched around the clock — nights, weekends, and holidays — so you never go without heat in winter or cooling in the peak of summer.
Every technician carries EPA Section 608 Universal certification for refrigerant handling — required by federal law for working with R-410A, R-22, R-32, and all regulated refrigerants. Your system is serviced by technicians who handle refrigerants legally and responsibly.
Get the information you need to make confident HVAC decisions for your property.
Heat pumps offer both heating and cooling from a single outdoor unit, making them significantly more energy-efficient than furnaces for moderate climates. A heat pump does not generate heat — it transfers it from outdoor air, which requires far less energy than burning gas or running electric resistance coils. Modern cold-climate heat pumps with variable-speed inverter compressors operate effectively down to minus 15 degrees Fahrenheit, making them viable in most Texas locations. For Eagle Pass homeowners with natural gas access, a dual-fuel system — heat pump for primary heating paired with a gas furnace for backup during extreme cold — often provides the best balance of efficiency and performance. Heat pumps also qualify for federal tax credits under the Inflation Reduction Act. KIC Refrigeration evaluates your specific climate zone, insulation levels, and utility rates to determine whether a heat pump, furnace, or dual-fuel system is the smartest investment.
Most residential HVAC installations in Eagle Pass, TX are completed in 1 to 3 days depending on the system type, condition of existing ductwork, and complexity of the project. A straightforward furnace and air conditioner replacement on existing ductwork typically takes a single day — our crews arrive in the morning and commission the new system by afternoon. Heat pump conversions, ductless multi-zone installations with line sets routed through walls, and projects requiring new or modified ductwork may take 2 to 3 days. Commercial installations and whole-building systems can extend to a week. We schedule around your availability, coordinate all permits and inspections, and protect your flooring and walls throughout the process. Every installation concludes with a full system commissioning including airflow verification and refrigerant charge confirmation.
HVAC repair costs in Eagle Pass typically range from $150 to $500 for minor fixes such as capacitor replacement, contactor swaps, or thermostat wiring issues. Mid-range repairs like blower motor replacement or refrigerant recharging run $500 to $1,200. Major repairs — including compressor replacement, heat exchanger repair, or evaporator coil swap — cost $1,200 to $2,500 or more depending on equipment brand and system type. The final price depends on whether you have a furnace, heat pump, air conditioner, boiler, or ductless mini split, as parts and labor vary significantly between system types. Our NATE-certified technicians diagnose the issue accurately on the first visit, and KIC Refrigeration provides a written estimate with transparent pricing before any work begins. We never charge a diagnostic fee when you proceed with the recommended repair.
As a guideline for Eagle Pass homeowners, consider replacement when your system is 15 to 20 years old, when the repair cost exceeds 50 percent of a new system, when the equipment uses R-22 refrigerant which is no longer manufactured and costs $100 or more per pound, or when your system runs constantly without adequately heating or cooling your home. Additional indicators include frequent breakdowns — more than two per heating or cooling season — rising utility bills despite regular maintenance, uneven temperatures between rooms, and excessive noise or dust. The age thresholds vary by equipment type: air conditioners and heat pumps typically last 15 to 20 years, furnaces 20 to 25 years, and boilers 25 to 30 years. KIC Refrigeration provides honest repair-versus-replace assessments at every service call, including side-by-side cost projections for both options.
The ideal time for HVAC replacement in Eagle Pass is during the shoulder seasons — spring and fall — when demand is lower, equipment availability is highest, and scheduling is more flexible. Contractors are less booked during these periods, which means faster installation timelines and potentially more competitive pricing. You are also more likely to find manufacturer rebates, utility incentive programs, and promotional financing during off-peak months. From a technical standpoint, moderate temperatures allow your new system to be commissioned and tested under less extreme conditions. However, KIC Refrigeration completes HVAC installations year-round in Texas and can often start within days of your approved estimate, even during peak summer or winter demand. If your current system is showing signs of failure, do not wait for the perfect season — a planned replacement is always better than an emergency one.
Absolutely. Modern high-efficiency HVAC equipment can reduce heating and cooling costs by 20 to 40 percent compared to systems installed 15 or more years ago. The improvement comes from advances in compressor technology, variable-speed motors, and smarter controls. In Eagle Pass, upgrading from a 10-SEER air conditioner to a 16-SEER2 or higher unit delivers substantial monthly savings — the higher the SEER2 rating, the less electricity consumed per BTU of cooling. On the heating side, replacing an 80-percent AFUE furnace with a 96-percent modulating furnace means that 16 cents of every heating dollar previously wasted up the flue now heats your home. Heat pumps offer even greater efficiency, delivering 2 to 4 times more heating energy than they consume in electricity. KIC Refrigeration calculates projected energy savings for any equipment upgrade so you can see the return on investment before making a decision.
Thousands of satisfied customers — here is what a few of them had to say.
"KIC Refrigeration did a full HVAC inspection before we closed on our new house. Very detailed report and the inspector answered all my questions patiently."
"Our AC went out on the hottest day of the year and they had someone here within two hours. Fixed it fast and explained everything clearly."
"Had three quotes for a heat pump installation and went with these guys. Best decision — the install was clean, efficient, and they handled all the permits."
Our NATE-certified crews provide HVAC service throughout the surrounding area.